AU 706 Minor Project & AU 707 Industrial Training AU, 7th (V) Semester Revised syllabus Automobile Engineering(AU)

AU 706 Minor Project & AU 707 Industrial Training Syllabus

 RGTU/RGPV Minor Project & AU 707 Industrial Training Syllabus

Automobile Engineering AU 7th Semester Syllabus 

AU 706 Minor Project 

Max. Marks-50
Min. Marks-25-

Credits 4C -P4

Provision of Minor project is made as preparation phase-I for major project or to take it as an
independent small project. For details of project see AU-805- Major project

AU 707 Industrial Training Course Contents:

Max. Marks-30
Min. Marks-15

Credits 2C-2P

Objective of Industrial Training
The objective of undertaking industrial training is to provide work experience so that students engineering knowledge is enhanced and employment prospects are improved. The student should take this course as a window to the real World and should try to learn as much as possible from real life experiences by involving and interacting with industry staff. Industrial training also provides an opportunity to students to select an engineering problem and possibly an industry guide for their Major Project in final semester.

Scheme of Studies:
Duration: Minimum 2 weeks in summer break after VI semester, assessment to be done in VII semester

SCHEME OF EXAMINATION
For the assessment of industrial training undertaken by the students, following components are considered with respective weightage.

(A) Term work In Industry (Marks allotted)

1. Attendance and General Discipline (05)
2. Daily diary Maintenance (05)
3. Initiative and Participative attitude during training 10)
4. Assessment of training by Industrial Supervisor/s (10)
Total (30)

(B) Practical/Oral Examination (Viva-voce In Institution (Marks allotted)
1. Training Report (15)
2. Seminar and cross questioning (defense) (15)
Total (30)

Marks of various components in industry should be awarded to the student, in consultation with the Training and Placement  Officer (TPO)/ Faculty of the institute, who must establish contact with the supervisor/ authorities of the organization where, students have taken training, to award the marks for term work. During training, students will prepare a first draft of the training report in consultation with the section incharge. After training they will prepare final draft with the help of the TPO/ faculty of the institute. Then, they will present a seminar on their training and will face viva-voce on training in the institute.

AU-705 Computer Aided Egineering and FEM AU, 7th (V) Semester Revised syllabus Automobile Engineering(AU)

AU-705 Computer Aided Egineering and FEM Syllabus

 RGTU/RGPV Computer Aided Egineering and FEM Syllabus

Automobile Engineering AU 7th Semester Syllabus 

AU-705 Computer Aided Egineering and FEM Course contents

Unit-I Introduction : Structural analysis, objectives, static, Dynamic and kinematics analyses, Skeletal and continuum structures, Modeling of infinite d.o.f. system into finite d.o.f. system, Basic steps in finite element problem formulation, General applicability of the method.

Unit-II Element Types and Characteristics : Discretization of the domain, Basic element shapes, Aspect ratio, Shape functions, Generalized co-ordinates and nodal shape functions; ID bar and beam elements, 2D rectangular and triangular elements; axis-symmetric elements.

Unit-III Assembly of Elements and Matrices : Concept of element assembly, Global and local coordinate systems, Band width and its effects, Banded and skyline assembly, Boundary conditions, Solution of simultaneous equations, Gaussian elimination and Choleksy decomposition methods, Numerical integration, One and 2D applications.

Unit-IV Higher Order and iso-parametric Elements: One dimensional quadratic and cubic elements, Use of natural co-ordinate system, Area co-ordinate system continuity and convergence requirements, 2D rectangular and triangular requirement.

Unit-V Static Analysis: Analysis of trusses and frames, Analysis of machine subassemblies, Use commercial software packages, Advantages and limitations

Unit-VI Dynamic Analysis: Hamilton's principle, Derivation of equilibrium, Consistent and lumped mass matrices, Derivation of mass matrices for ID elements, Determination of natural frequencies and mode shapes, Use of commercial software packages.

References:
1. Gokhle Nitin; et al; Practical Finite Element Analysis; Finite to Infinite, 686 Budhwar Peth, Pune.
2. Logan DL ; A First Course in Finite element Method; Cegage
3. Krishnamoorthy; Finite Element Analysis, theory and programming; TMH
4. Buchanan; Finite Element Analysis; Schaum series; TMH
5. Seshu P; Textbook of Finite Element Analysis; PHI.
6. Chennakesava RA; Finite Element Methods-Basic Concepts and App; PHI Learning
7. Reddy JN; An introduction to finite element method; TMH
8. Desai Chandrakant S et al; Introduction to finite element Method; CBS Pub
9. Hutton D; Fundamentals of Finite Element Analysis; TMH
10. Zienkiewicz; The finite element Method; TMH
11. Martin and Grahm; Introduction to finite element Analysis (Theory and App.)
12. Rao, S.S., The Finite Element Method in Engineering; Peragamon Press, Oxford.
13. Robert DC., David DM et al, Concepts and Application of Finite Element Analysis; John Wiley.
14. Chandrupatla, T.R. an Belegundu, A.D., Introduction to Finite Elements in Engineering,PHI

AU-704 Combustion and Heat Transfer AU, 7th (V) Semester Revised syllabus Automobile Engineering(AU)

AU-704 Combustion and Heat Transfer Syllabus

 RGTU/RGPV Combustion and Heat Transfer Syllabus

Automobile Engineering AU 7th Semester Syllabus 

AU-704 Combustion and Heat Transfe Course contents

Unit-I Combustion: Combustion phenomena of S.I. and C.I. engines, Stages of combustion- Photographic studies of combustion process- p-q diagrams in S.I. and CI engines. Abnormal combustion-Effect of engine variables on knock-Factors controlling combustion chamber design. Combustion chambers: Diesel engine combustion chambers open, Divided, Swirl, Turbulent and Ricardo's M Combustion chambers. Unit-II Heat Transfer in IC engines: Heat transfer, Temperature distribution and thermal stress in Piston, Cylinder Liner, cylinder head, Fins and valves. Variation of gas temperatures, Heat transfer coefficient and combustion system-Effect of engine load on piston temperature heat rejected to coolant quantity of water required.

Unit-III Measurements Flow meters-Volumetric type, gravimetric type-fuel consumption measurement in vehicles-Air consumption: Air box method, viscous air flow meter; flame temperature
measurement and pressure measurement.

Unit-IV Introduction to heat transfer: Temperature, Heat and thermal equilibrium, Modes of basic laws of heat transfer i.e. conduction, Convection and Radiations; Fourier equation and Thermal Conductivity, Derivation of the general form of heat conduction equation in Cartesian, Cylindrical Spherical Coordinates.

Unit-V Conduction Heat Transfer: Steady State Conduction, Heat conduction through plane wall, Composite wall, cylindrical wall, Multi layer cylindrical wall, and through spheres; effect of variable conductivity, Critical thickness of Insulation; conduction with heat generation, plane wall with uniform heat generation, Dielectric heating, Cylinder with uniform heat generation, Heat transfer through Piston crown. Heat transfer from extended surface, steady flow of heat along a rod, Governing differential equation and its solution, Heat dissipation from and infinitely long fin, Fin performance.

Unit-VI Convection Heat Transfer: Free and forced convection, Laminar and Turbulent flow, Newton- Rekhman Law: Convection rate equation, Nusselt Number; radiation heat exchanger; salient features and characteristics of radiation, Absorptive, reflectivity and transmittance; spectral and spatial energy distribution, wavelength distribution of black body radiation, Plank's law; total emissive power: Stefan Boltzman law, Wien's displacement law, Kirchoffs Law, gray body and selective emitters

References:
1. Arora and Domkundwar, Heat and Mass Transfer
2. D.S. Kumar, Heat and Mass Transfer.
3. Frank Kreith, Heat Transfer
4. P.M. Heldt, Internal combustion engines.
5. V. Ganeshan Internal combustion engines.
6. Eckert and Drake, Introduction to heat transfer.
7. Jakob and Hawkins, Elements of Heat Transfer
8. Holman, Heat Transfer
9. S.P. Sukhatme, Heat Transfer
10. Kothandaraman, Heat Transfer Data Handbook.

List of experiments (please expand it);
Combustion and Heat Transfer AU-704
1 Conduction through a rod to determine t
2 Thermal conductivity of material
3 Forced and free convection over circular cylinder
4 Free convection from extended surfaces
5 Parallel flow and counter flow heat exchanger effectiveness and heat transfer rate
6 Calibration of thermocouple
7 Experimental determination of Stefen-Boltzman constant

AU-703 Mechanical Vibration and Noise Engineering AU, 7th (V) Semester Revised syllabus Automobile Engineering(AU)

AU-703 Mechanical Vibration and Noise Engineering Syllabus

 RGTU/RGPV Mechanical Vibration and Noise Engineering Syllabus

Automobile Engineering AU 7th Semester Syllabus 

AU-703 Mechanical Vibration and Noise Engineering Course Contents:

 Unit 1: Fundamental Aspects of Vibrations: Vibration, main causes, advantages and disadvantages; engineering applications of vibration and noise; vector method of representing harmonic motion; characteristics of vibration, harmonic analysis and beats phenomenon, work done by harmonic forces on harmonic motion; periodic, non-harmonic functions- Fourier series analysis; evaluation of coefficients of Fourier series; elements of vibratory system; lumped and distributed parameter  systems.

Undamped Free Vibrations: Derivation of differential equation of motion: the energy method, the method based on Newton’s second law of motion, and Rayleigh’s method. Solution of differential equation of motion: Natural frequency of vibration. Systems involving angular oscillations: the compound pendulum.

Unit 2: Damped Free Vibrations: Viscous damping: coefficient of damping; damping ratio; under damped, over damped and critically damped systems; logarithmic decrement; frequency of damped free vibration; Coulomb or dry friction damping; frequency, decay rate and comparison of viscous and Coulomb damping; solid and structural damping; slip or interfacial damping.

Unit 3: Harmonically excited Vibration: One degree of freedom- forced harmonic vibration; vector representation of forces; excitation due to rotating and reciprocating unbalance; vibration Isolation, force and motion transmissibility; absolute and relative motion of mass (Seismic Instruments ). Whirling Motion and Critical Speed : Whirling motion and Critical speed : Definitions and significance. Critical speed of a vertical , light flexible shaft with single rotor : with and without damping . Critical speed of a shaft carrying multiple discs (without damping ), Secondary critical speed.

Unit 4: Systems With Two Degrees of Freedom : Un-damped free vibration of 2 d.o.f and Principal modes of vibration; torsion vibrations; Forced, Un-damped vibrations with harmonic excitation ; Coordinate coupling; Dynamic vibration absorber; torsion Vibration Absorber; Pendulum type of dynamic vibration.

Unit 5: Noise Engineering Subjective response of sound: Frequency and sound dependent human response; the decibel scale; relationship between, sound pressure level (SPL), sound power level and sound intensity scale; relationship between addition, subtraction and averaging, sound spectra and Octave band analysis; loudness; weighting networks; equivalent sound level, auditory effects of noise; hazardous noise, exposure due to machines and equipments; hearing conservation and damage risk criteria, daily noise doze.

Noise: Sources, Isolation and Control: Major sources of noise on road and in industries, noise due to construction equipments and domestic appliances, industrial noise control, strategies- noise control at source (with or without sound enclosures), noise control along the path (with or without partitions and acoustic barriers ); noise control at the receiver, ear defenders, earplugs, semi-insert protectors.

References:
1- Ambekar A.G.,’ Mechanical Vibrations and Noise Engineering; PHI
2- Meirovitch Leonard; Element of Vibration Analysis; TMH
3- Dukikipati RV Srinivas J Text book of Mechanical Vibrations; PHI
4- Kelly SG and kudari SK; Mechanical Vibrations; Schaum Series;TMH
5- Thomson , W.T., Theory of Vibration with Applications , C.B.S Pub & distributors .
6- Singiresu Rao, ‘Mechanical Vibrations , Pearson Education .
7- G.K. Grover, ‘ Mechanical Vibration , Nem chand and Bross , Roorkee .

List of experiments (please expand it);
1- To find out effect of load on natural frequency of vibrations of a lever pin supported at one end carrying adjustable load on a vertical screwed bar and spring supported at some intermediate point (i) When the dead weight of rods is neglected and (ii) when their dead weight is taken into account .
2- To find out frequency of damped free vibration and rate of decay of vibration-amplitude in the system.
3- To find out natural frequency and damped free frequency of a torsion pendulum and , hence to find out coefficient of damping of the oil ;
4- To observe the phenomenon of ‘whirl’ in a horizontal light shaft and to determine the critical speed of the shaft.
5- To observe the mode shapes of a spring-connected, double pendulum and hence to demonstrate the phenomenon of beats.
6- To demonstrate the principle of tuned Undamped Dynamic Vibration Absorber and to determine the effect of mass-ratio (of main and auxiliary mass) on the spread of the resulting natural frequencies ;
7- To take measurements of sound Pressure Level (SPL) and to carry out octave band analysis of a machine using Noise Level Meter.

AU-702(D) MIS ERP and e-Business AU, 7th (V) Semester Revised syllabus Automobile Engineering(AU)

AU-702(D) MIS ERP and e-Business Syllabus

 RGTU/RGPV MIS ERP and e-Business Syllabus

Automobile Engineering AU 7th Semester Syllabus 

AU-702(D) MIS ERP and e-Business Course contents

 UNIT 1 Management Information System (MIS) definition, Objectives and benefits, MIS as strategic tool, obstacles and challenges for MIS, functional and cross functional systems, hierarchical view of CBIS, structured and unstructured decision, Operation and mgt support, Decision process and MIS, info system components and activities, Value chain and MIS support.

UNIT 2 System concepts: types, definition, characteristics, feedback (Pull) and feed-forward (Push) control, system stress and entropy, computer as closed system, law of requisite variety, open and flexible (Adaptive) systems, work system model and comparison with input-process-output model, five views of work system: structure, performance, infrastructure, context and risk and their effect on product performance.

UNIT 3 Info concepts: define data, info, knowledge, intelligence and wisdom, Information characteristics and attributes, info measurement and probability, characteristics of human as info processor.

UNIT 4 Planning and control Concepts: terminologies, difficulties in planning, system analysis and development plan-purpose and participants, info planning, (SDLC) system development life cycle for inhouse and licensed sw, system investigation, analysis of needs, design and implementation phases, training of Operational personnel, evaluation, Control and Maintenance of Information Systems.

UNIT 5 E-business components and interrelationship, Evolution of Enterprise Resource Planning (ERP) from MRP, Supply chain management (SCM) and Customer relationship management (CRM), Integrated data model, strategic and operational issues in ERP, Business Process Re-Engineering (BPR), significance and functions, information technology and computer NW support to MIS.

References
1. Davis and Olson, Management Information Systems, TMH
2. James O’ Brian, Management Information Systems, TMH
3. Oz, Management Information Systems, Cengage
4. Alter Stevenson, Information Systems: Foundation of E-Business; (Prentice-Hall,USA)
5. Jayaraman, Business Process Re-Engineering, TMH.
6. Garg. V.K.; ERP, PHI
7. Kelkar SA; Management Information Systems A Concise Study; PHI Learning.
8. Radhakrishnan R and Balasuramanian S; Business Process Reengineering; PHI Learning.
9. Alex Leon ; ERP, TMH
10. Jawadekar WS; MIS- text and cases; TMH
11. Jaiswal M and Mital M; MIS; Oxford higher Edu India